Posted on Leave a comment

Expensive or cheap equipment?

Many of us make a mistake at the very beginning and choose the wrong equipment. The detector should be adapted directly to the conditions that prevail at the workplace as well as expectations regarding the finds. Half the poverty when we are looking for ordinary places without a lot of iron or civilization garbage. In such places, ordinary simple equipment for a few hundred zlotys is enough.

The problem begins when the soil is highly mineralized and we have a high content of iron, ceramics, turf ores, and coke. It turns out that ordinary equipment does not work at all. Did not work. Half the trouble is when we are able to determine it organoleptically and it can be seen from the behavior of the detector. The device energizes, the depth of detection decreases, the ID signaling simply does not work, and the excess iron causes the device to clog and shift in the scale of rusty corrosion to the range of high conductors such as silver. swept away. You can hang the equipment on a peg. There is no topic.

Fortunately, there are several ways to avoid problems. It is known that it is best to buy a high-end detector such as Tarsacci MDT 8000 or XP DEUS II … but who can afford such extravagance nowadays?

We start from scratch. If our equipment has the All Metal mode, we start it immediately. Discrimination is the enemy of every Seeker. End and period. In this way, we improve the performance and the electronics have fewer signals to filter, it is faster and there is less chance that we will miss something. We also start to sweep slower and more accurately. Surveying is fundamental. We assume every move and absolutely parallel to the ground.

Too much interference and false signals? We detune and reduce the sensitivity. It is also worth raising the probe a little higher. Sometimes it helps, also in the case of searching for signals on the surface – a lost wedding ring.

App. Yes, application. I send furious Janusz with the police syndrome to hell. The application is not a record of the services, but a help for you. What? Simple, we see how much we’ve walked and what signals were shown in a given place. You can observe the concentration of finds. You don’t have to upload photos, just a letter marker of the item. On this basis, it is known where to return with other equipment and or improve with the help of the selected program or a new set of settings.

Ground calibration. Just as important as detuning from EMI interference. The basis, the essence of working with the detector. Done right is a chance for success, screwed up is time wasted. Firstly, we look for a clean place, secondly, we double-check. When calibrating, we look at the values, compare, go to another place and try again. Correct identification and depth of detection depend on it. The measurement value tells us what conditions we can face.

Mineralization index. Not every metal detector has it. We check what it shows, and on this basis we are able to predict how much we will lose performance in this place and how to set the equipment exactly.

In the end, there’s always a fat wallet. Does the place produce? Are there results? It’s worth investing in better equipment! Multi-frequency device or in t hybrid technology, pulsed? Why not! Such solutions allow you to break through the iron layer in a more effective way. Equipment doesn’t have to cost a fortune. All the time on the market we will find garage producers who can work wonders. Currently, PI impulse detectors have discrimination and identification, it does not work as well as in popular VLF devices, but it allows you to reopen old places that apparently do not produce anything new!

No one would have believed a few years ago that the so-called. the frames will be in a version with full discrimination and in IB technology. Looking for a big color? No problem, a good example is Pathfinder Nexus, described in one of the articles of this blog.

If you liked this article, give it a like and remember our social media:

Youtube
Sklep Omnitron
Omnitron Metal Detecting Group
Intagram

 

 

 

 

Posted on Leave a comment

NEXUS Pathfinder V2 hellish frame with discrimination

The frame detector or the popularly known frame is a really great solution for the big game, but unfortunately also very demanding when it comes to the application itself. Everything has to be carefully thought out because the choice is wide and the possibilities are practically unlimited.

The NEXUS company needs no introduction. This is the world of analog detectors, unreasonably expensive, complicated, and IB technology.

So what is the difference between NEXUS products and others, apart from the quality of workmanship? In addition to performance, this type of two-box allows for quick movement over rough terrain and can only be operated by one person. It has discrimination and we are free to choose the type of guide we are looking for! Color or iron and smooth adjustment. Story!

YouTube player

Brilliant solution, considering that with a probe size of 20 inches, we see objects the size of soda cans and larger! There is no problem with small garbage that can make life unbearably difficult. To this, we will add a choice of operating modes: static and dynamic, ground calibration, and mineralization compensation. The extreme amount of iron is not a hindrance, and the device is made of aluminum and carbon fiber and can be quickly folded. The weight is about 4.5 kg, quite bearable.

Finally, the speed of work and we have a really nice daemon that is handy and easy to use. What is the voltage on the probes, I’m afraid to ask, and the large heat sink below the control panel is impressive. Below is a table presenting the capabilities of the Nexus Pathfinder V2.

Posted on Leave a comment

XP DEUS II program OMMONO

XP in the new DEUS II metal detector model implemented the old model in the form of the DEUS MONO program. Less clever people will tell me why I have a set of programs working in several frequencies at once, i.e. more stable, more resistant to worse conditions, and better signaling different conductors from both ends of the scale (silver and gold = wealth). So why single frequencies?!

The reason is simple, the device needs less time to process the data of only one frequency, and a well-chosen one can make it possible to reach a little deeper. The lowest frequency is 4 kHz and the highest is 40 kHz. Each of them has its advantages and disadvantages. Low is really deep and favors high conductors such as silver and large pieces of iron, high will better cope with heavy debris and high mineralization with fine and low conductors such as gold and small silver coins.

We sacrifice stability and try to squeeze everything we can out of the detector. Below is the OMMONO program especially for you:

The XY chart will help you identify:
Options/Configuration/Profile/XY

Menu:

  • Discrimination 6.1 at the beginning, EXPERT – PITCH tab (LEVEL translation error for software version 0.17)
  • Sensitivity to maintain stable operation
  • Frequency 4 kHz or 40 kHz description of what to choose and for what above
  • Iron volume 3 or zero if it will be too loud in the place
  • Base reactivity 1.5 set under conditions (trash 2 up)
  • Acoustic signal 4

Calibrate to the ground in a clean place, check the values in another, here manual ground calibration by the so-called. pumping or choosing a value is essential.

Posted on 2 Comments

XP DEUS II PROGRAM OMRELIC

The RELIC program in the new XP DEUS II detector is a kind of Holy Grail because it works on a completely different principle than other programs. It is closer to the Gold Field version, which is a typical program for searching for gold nuggets, also known as the ORX model. The multi-frequency characteristics do the job, especially in iron. The frequency oscillates around 24 kHz, which is optimal even on the more difficult ground and there is no great loss of depth.

IAR discrimination works by size rejection of the iron signal, but you can read about it elsewhere on my blog or watch a video on my Youtube channel. I recommend the XP DEUS II playlist for dummies!

YouTube player

So how do you properly set up the RELIC program to go really deep? We know it’s the deepest program next to DEEP HC, but how to squeeze more out of it? In the beginning, you choose the REACTIVITY responsible for the separation of objects. For me, the starting point is 1.5. For more cluttered places, I recommend 2 or even 3. A higher value means less performance when it comes to depth, but better separate objects. Here you have to adjust everything to the place and quantity – the intensity of the signals. Along the way, we set the sensitivity to the level of stable operation, we scan the channels so that the device automatically selects the most stable operating range.

The volume of the iron, the lead signal is already a personal preference, as is the amplification of weak signals. It is worth leaving the factory settings as the default. The leading signal THRESHOLD we need to raise a bit (software version 0.71).

We come to the most important thing – IAR discrimination. Here I set a maximum value of 3 to avoid losing low and fine gold guides, above this value, we risk more. A higher parameter gives less low signals and guarantees more stable operation. By entering the EXPERT tab, we can set NOTCH. In this case, it is a kind of audio discrimination that does not affect the performance of the detector, but unfortunately, very deep signals can give a value of 00 on the display. Fortunately, we will only lose the audio and the values are still displayed. It is important because 00 is a value close to the reading of the soil and also ceramics, which is a testimony of human presence in a given area.

You can always use NOTCH, it increases the comfort of work and translates into results. If the signals are bothering you, you can try to set the range from 00-06. You will not be overloaded with signals from rusty iron and over-response of the soil. There is always a risk of losing items masked next to this value, deep without ID as I wrote above. It is worth choosing settings for a given scenario or a search strategy you have developed in a given place.

Below is the OMNITRON program especially for you!

Remember to subscribe and get discounts (click):

Youtube
Sklep Omnitron
Omnitron Metal Detecting Group
Intagram

 

Program OMRELIC:

The XY chart will help you identify:
Options/Configuration/Profile/XY

Menu:

  • Discrimination IAR 3 (5 in the case of a large trash and large iron objects – note the risk of losing low conductors above 3) + EXPERT tab and set NOTCH to 00 or in the range of 00-06
  • Iron volume 3
  • Base reactivity 1.5 set under conditions (trash 2 up)
  • Acoustic signal 5
  • Leading signal 10 up or under your preference
  • Sensitivity to the level of stable operationScan the channels before starting work and when it loses stability. Hold the right panel arrow at the top. Perform a ground calibration as a last resort in a clean area if stability is a problem.

 

 

 

 

Posted on Leave a comment

A burnt field or a duel of an analog with a TV set

Is it possible to compare the analog detector DeepTech VistaX to XP DEUSA II? Theoretically yes, although in practice the disproportions are really large that it is impossible to put both devices together directly.

Weight, portability, compactness, and reconfigurability, build quality unbeatable in favor of XP. Audio also gives you more possibilities. Another shelf and another league of equipment, not to mention the price. For one XP DEUS II, we will buy exactly three VistaX!!!

When it comes to working in a littered area, it will also be a bit easier for us, but with one small exception, we will dig less, but we can skip more. In the case of an analog, you need to check and dig. An apparent disadvantage becomes an advantage in a very good seat! Unreliable signal with a bad ID on the display and we will miss the good one, and without we have to check it! A lot of masked signals and coins on the edge are easy to mine! It’s the whole analog mystery. There is something more.

In difficult terrain with a lot of iron, the devices go head to head with one small exception, the analog is always deeper and the difference is really noticeable, which we could check on the passing spot – the so-called. burnt. Easy sandy soil with a settlement base of iron, burnt coal, coke, and pottery. There, both detectors feel really good. The dot over and the nature itself put in the form of a shower, improving performance, but also increasing the risk of excitation of detectors on wet grass.

YouTube player

Both detectors had 11-inch probes. XP DEUS II worked in Deep HC or Relikt. Devices turned to maximum sensitivity. Reactivity in XP set to 1.5 along with a very slow sweep and cross-checking of signals did the job.
The difference is significant where XP, which is really deep, still has 2-3 cm of the reserve before it loses the signal, VistaX is easily over 5 cm deeper! Double discrimination gives you a chance to check the item under the probe. In some situations, the XP was already operating at the edge of the range, where the analog signal was still strong and reliable. At one point, after digging a 50 cm hole, we thought it would be a piece of rusty iron, but no! An object half the size of my little finger was in the dimple!

We must admit one more advantage of both devices, well-calibrated almost to the end of the scale signal – they show well the type of conductor (color or iron). We avoid the dilemma of digging up rusty scrap at the edge of the range… although this scrap can often be worth checking out!

The question is what will be the difference with VistaX with a 14-inch probe… another 5 cm is very real. Unfortunately, there are also disadvantages, a large probe means more mass, poorer balance and separation, and slower sweep. We’ll try to check it. Remember to subscribe and comment below the article!

 

Posted on Leave a comment

Nokta Makro The Legend vs XP DEUS II

How hard it is to compare currently produced detectors does not need to convince anyone. Price is no longer the only exponent.

The competition among manufacturers has come full circle, and the data alone will be of little use for a simple reason, which is the device software. To make matters worse, the popular software update can mess up a lot and turn an average detector into a wolf in sheep’s clothing. Unfortunately, it also works the other way around.

Nokta Makro The Legend and XP DEUS II are connected only by multi-frequency technology, all the rest is diametrically different, maybe apart from the quality of workmanship, in which the Turkish manufacturer tries to catch up with the competition and he does it really very well. The wireless Frenchman is a class by itself and no one has beaten the 960-gram weight of the device so far. In heavy terrain, such parameters speak with each subsequent swipe, and the modular design allows you to change the configuration.

There will be those who will complain that you can’t buy traditional batteries and everything has to be charged separately. This has never happened to me – a power outage. Fortunately, the multitude of modules allows you to resign from the discharged RC panel and use headphones in its place … there are some emergency options.

Let’s get down to earth. The Legend is also solidly built and won’t let you down in the field. It’s not XP’s build quality, but the price is half the God of Detectors. a lot? That’s possible. The Legend convinces with its ease of use and very strong integration with the user. After a while we understand everything, and quiet and stable work is a real pleasure. Audio, yes, audio finally exists and is doing well, especially since we can change a lot. It’s not a symphony from DEUSA II, but it’s closer than farther. The clear detector does the job as it should and that speaks to me. Symbiosis and pleasure. DEUS II is a much more difficult device or is it worse? No. It just requires much more time to master and understand the dependencies of the settings. When will it pay off? In very difficult and specific conditions such as a very large amount of iron. In such a place, XP shines and a title that was not given to it by chance. A large number of settings allow you to adjust the equipment to yourself and the environment. This is a big advantage, but also something that requires a lot of constipation and time. As you can see on social media, many have given up and are putting our Detector God up for sale.

So how to choose? Smart, and so serious? For 90% of Nokta Makro The Legend is enough and will make us really happy. On the same littered meadow, I was better with the Turk than with the French, but I know that it was a medium difficult place, and I would take XP to the rubble of the old inn. DEUS II is a great solution when someone needs lightweight equipment due to injuries or hard-to-reach terrain. It is also a tool to work in a large garbage can and in a huge amount of iron, which makes other devices simply ineffective.

Depth? Both detectors have enough of it. All in the video below. Remember to subscribe!

YouTube player
Posted on Leave a comment

Tarsacci MDT 8000 how to set up?

How to set up the Tarsacci MDT 8000 detector correctly? The device has a clear and simple menu, without any hidden functions, but still requires a lot of time to take advantage of the new technology, which is not used by any other manufacturer.

The first and key choice is the operating frequency of our detector. We choose from 6.4 to 18 kHz. Interestingly, even a low frequency allows us to detect very small objects in size … well, the charm of PI (pulse induction) used in this hybrid. Lower frequency means better performance – depth, but also worse separation of objects in cluttered terrain. It is also better for signaling coin-shaped and volume objects, as opposed to foil or pieces of aluminum.

Another workflow problem. We have three types: all metal, discrimination, and mixed mode. All Metal will be good for virgin spots, where the signal appears from the holidays. We only have one and we have to look at the ID displayed on the screen. DISC is the only right solution for total trash. The signal is short and if it is repetitive you have to dig. The mixed mode gives us additional information about the size and depth of the object. Places clean or moderately littered.

Before we start, we look for a clean place and calibrate to the ground, if we still have a signal from the ground, we increase the value by 50, this should mute the device. Next, we hear the response of the ground. We can try to use the SALT function – salinity level. We pump the probe traditionally above the soil and adjust the value to mute the response. The starting point is 29. Finally, we are left with THRESHOLD – TRH. You have to be careful here. Too high a value and we lose ranges and we will not hear small objects. We always set the limit. If the ID shows low values when sweeping the probe, we need to compensate with this function.

Iron breaking through the scale and falling into color can be handled by using a DISC value of -29 or +26. Finally, there is the sensitivity adjustment. It’s not worth exaggerating. MDT 8000 already at a value of 4 is deeper than most known detectors. We eliminate all instabilities and interferences by reducing the sensitivity or changing the frequency.

I am curious about your opinions on the Tarsacci MDT 8000 detector, write under this post.

YouTube player
Posted on Leave a comment

XP DEUS II program GENERAL

The GENERAL program is the basic solution for the XP DEUS II detector. A starting point from which to start, but also a good base for learning and later modifications for your needs.

There are no universal solutions and if someone believes something like that, they are simply naive. Just like ready-made programs for anything and everything. We always start by choosing a program tailored to the subject of the search. For the multi-frequency version, we are looking at the frequency range. Their range will tell us whether the object of our interest will like them. Low conductors like gold love high frequencies, and silver the opposite. This is our primary indicator. Very difficult conditions and tons of iron, maybe it’s worth trying on a single frequency with the DEUS MONO program?

We return to the basic program. We start with setting the REACTIVITY, the most important parameter that affects the performance of the device, such as depth and separation of objects placed next to each other. A higher value and the detector becomes shallower, but it separates objects better, lower and we have a greater depth, but we have to sweep slower and we may not hear a coin placed next to iron, e.g. a nail. So how to choose the settings? We check what is happening under the probe and make a decision. We can experiment with different settings and see how it affects signaling and ranges.

The next step is the GB tab and selecting the GROUND STABILIZER function, a type of filter that affects the response of the substrate. The default value is 2, which is a medium mute level. At level 1, you can walk with some experience. The detector becomes less stable, but a little more can be heard. The end of the scale is a value of 3, the perfect compromise for soils that have a lot to say and make our lives miserable in the form of disturbances. We return to the filter called SILENCER, another compromise between performance and comfort of work, allowing us to eliminate crackling caused by iron elements in the substrate. A high value causes less interference, a lower value ensures that we can hear more again.

We are left with the choice of the type of audio. PWM or SQUARE is a personal preference. We have to answer the question of how much of an orthodox Deusiarz (PWM) or Minelab lover (SQUARE) we have in us. Sensitivity settings or calibration to the soil in a given place probably do not need to be explained, we still have audio and the choice of the number of tones. It depends on the place and personal preferences – your hearing.

The rest is hard training and a lot of work is put into settings and understanding. Without it, there is no chance of results. If you have any questions, comment directly under the video.

 

 

Posted on Leave a comment

XP DEUS II program RELIC

I spent last Sunday testing the XP DEUS II metal detector. I can’t get rid of the RELIC program. Unfortunately, habits probably prevail over reason, but one by one.

As we know, this program is similar to the well-known DEUS I under the name GOLDFIELD. Yes, it’s a typical tool for finding gold nuggets. Discrimination called IAR (Iron Amplitude Rejection) works in a completely different way than the classic solution. The device rejects iron by volume, according to the signal strength, and it can be adjusted in the range from 0 to 5. The last value means the strongest – the largest objects/signals.

The program is not for everyone. Why? This is a typical All Metal, in which we have one signal, although modulated to low and high conductors. The iron is signaled by a low tone, the volume of which can be additionally adjusted. As I mentioned earlier, the IAR value determines its volume – the signal strength. In practice, this works great, provided that the area is not extremely cluttered and you can set the REACTIVITY value low, which gives us even better performance in the case of depth. The fact is, you have to sweep slower and use the XY chart (link on YouTube), which additionally supports identification.

Audio in the form of PITCH modulated tone depending on the signal strength with the superimposed PWM profile (DEUS I) or SQUARE (new audio closer to Minelab) also helps a lot. Audio amplification and lead level are also additional tools that greatly improve identification. It is worth setting them well for the conditions prevailing in a given place, thanks to which we have more control over what happens after the probe.

With good settings and not too mineralized soil, the detector is really very deep. I pulled out an old ornament from a good 40 cm, and the signal was tearing the headphones. Certainly, in a place where there is a lot of colored garbage and iron, it is worth using the FAST or GENERAL program, they set the filters (functions) appropriately for the prevailing conditions beforehand, or in the case of total garbage, try the DEUS MONO variant. Unfortunately, all this takes time and conditions, and these have recently been very scarce.

Posted on Leave a comment

How important is audio

How important audio is in the case of a metal detector, I don’t have to convince anyone. Someone somewhere wrote it’s a matter of taste… and yes and no. This is the main sense of this hobby, and you can read how important it is in the article below.

Example scenario. A beach filled to the brim with bottle caps. Do they give a beautiful high tone, and their flock next to each other? How to shell a coin?!
This is where smart audio comes to our aid. The first pioneer was Garrett using Iron Audio. If I’m wrong, please comment under this article. A special additional option and a low tone appear on the edges of our unfortunate cap, a break. We have a low, high, and low tone. There is also a disadvantage. You have to sweep slower because the sound is longer in time. It’s hard in a total dump, but you can catch the desired signals.
When we do not have such an option, there is no chance of finding, even a chart will not help us, we will lose a lot of time and nerves. A device not equipped with such a solution will become completely useless in the above scenario. Some manufacturers go further and the sound of the cap becomes intermittent or virtually disappears. Such an idea is also good because it shortens the time of signal emission and relieves the operator.

Why audio should be good and what does it mean? The human brain has a certain resistance to different types of sound. For example, the static noise in the production hall will tire us after a few minutes, as well as sounds of different intensities and frequencies. This type of load causes us to lose our orientation after some time. We will not be able to see what is a valid signal and what is not. The effect of fatigue and loss will completely take away our strength and pleasure from searching.
I’ve had this problem myself many times. For this reason, manufacturers use different versions of sounds. The best example would be XP DEUS II with new SQUARE audio. The sounds are even, melodious and soft to the ear, unlike the old PWM version known from the XP DEUS I model. They may carry slightly less information but are more absorbable in the long run.
Another thing is the change of sounds over time. The above break tells us whether we have a cap or rusty iron under the probe. Good audio saves us trouble. It is not always possible to dig up and check everything, especially when we work in a dump where someone has been throwing away garbage for several hundred years and plowing it cyclically with a plow. In this case, audio with additional information is a godsend.

You can also work in mixed mode, which carries additional information, if it is in the stereo version, then our brain acts as a computer and we hear delays between the static and dynamic channels. This way you can guess what kind of conductor is in the hole. For example copper or iron, or maybe silver? It takes a bit of practice, but it gives me a lot of satisfaction.
Returning to polyphonic sounds or the so-called multi tones. They give an immediate answer as to what object we are dealing with. After a short training, we can hear small breaks and nuances and we can determine with high probability how the tsar’s double-layer button beats, and how a silver coin is next to a nail. With really fast devices equipped with good audio, you can hear the length of the signal and know if the object is a small coin or something larger.
It’s the same with foil. An overdriven buzzing tone and there’s a chance we won’t dig up another cigarette pack remnant or burnt coke residue.

It’s worth trying something new, because it may turn out that our old and worn detector with a gong that sounds like a doorbell missed many interesting things! Like the hardware is too tight. Then we have the effect of long lights in the fog. Sounds blind us, or rather deafen us, just as audio amplification set too high does not allow us to hear the signals of ghosts, i.e. those deepest objects that we so desire.

The headphones I keep mentioning also help to maintain concentration, learn quickly, and easily recognize tones without fighting the noise of the wind and civilization.

I recommend checking the audio line of other devices, even a few moments on equipment borrowed from a friend gives us a subjective comparison. It is worth choosing a detector whose audio was designed by a seeker, not a programmer, and if the first one was a musician, you’ve come to the right place!

Posted on Leave a comment

Clash of the Titans

The recent debut of XP DEUS II gave me a lot to think about. You can still feel the legacy of Whites Spectra in such an edition that it should be praised. The French company coped with this challenge quite well. Everything else is well known to us and things like wireless or featherweight no longer shock us. The novelty is water resistance up to 20 meters, which opens up completely new possibilities.

How does the TARSACCI MDT 8000 fare against this background? Many people would like to know what is the difference. The build quality and carbon fiber used put it truly in a class of its own, but the DEUS II leads the way here by the full length. It’s good, but as we know, everyone is one step behind and it’s been like this for many years. The weight of 1300 grams is currently the standard in the class of professional devices. Technically, however, we live in two different worlds. DEUS II is a multi-frequency metal detector, while MDT 8000 is a hybrid of VLF and PI (pulse induction) technologies.

So what is the advantage of such a solution? The technology is pioneering and patented in the USA and Europe, but does it really give you something more to spend your last pennies on this detector?

Just carry out a simple test and everything becomes clear. TARSACCI allows you to maintain a stable and unchanging ID in the close presence of small pieces of foil, magnetic stones, or high salinity or high mineralization. This advantage makes the device more resistant to masking. It will cope with more difficult conditions without changing the reading due to the presence of the above-mentioned disturbances and without limiting the depth.

A simple test gives the answer. By sweeping a piece of foil the size of a coin and a coin 5-10 cm above it just in front of the TARSACCI probe we have a fixed and non-changing ID. The foil does not change our signal, similarly, coke and rocks, and iron do not have such a big impact. For the sake of accuracy, we are talking about coin-sized items here. The same test in the case of DEUS II already gives a significant drop in ID.

The advantage of the last XP is multi-frequency, which allows the signaling of equally clear objects from both ends of the scale. Even for low and high conductors. Fine gold as well as heavy silver. The performance may be slightly worse, but in the case of one frequency, it will be slightly better. We have to answer the question what are we interested in? Good signaling of various objects or less masking effect in very difficult conditions? It all depends on the place and subject of the search.

Both models of detectors have the ability to fine-tune settings. DEUS II has more possibilities, and the MDT 8000 is simplified to such an extent that for professional equipment from the top shelf, it is simply strange. The producer decided to put everything on one screen. There are no drop-down submenus like in XP. We see everything at a glance and we don’t have to check if one of the many filters is definitely well-selected and does not affect our performance.

In conclusion, the race is fierce and it is difficult to pick a winner and compare both detectors directly. TARSACCI is more of a Swiss army knife, equipment for heavy and complicated scenarios, where high mineralization or salinity requires the use of a heavy caliber. DEUS II is a versatile, fun metal detector that is lightweight and waterproof, with great configurability and wireless connectivity to make your life easier.

Please remember to subscribe to my YouTube channel and social media on Facebook and Instagram. Links below.

Youtube:

https://www.youtube.com/channel/UCa7McxkrH2DNavMWcOBFU2g

Facebook:

Omnitron Store:

https://www.facebook.com/Omnitron-318061209114734

Omnitron Metal Detecting Group

https://www.facebook.com/groups/340050200024326

Instagram:

shop_omnitron

 

Posted on Leave a comment

New accessories for XP DEUS

I am honored to introduce you to the new accessories for XP DEUSA I and II, designed and made by us. It is a special stand weighing 21 grams to prevent the detector from tipping over in the field and a cover for the wear-off tip of the pinpointer from the Mi 4 and 6 families.

Posted on Leave a comment

XP DEUS II program RELIC and IAR

The new XP DEUS II surprises. I mean this seriously because over the last few years my DEUS I has been dusting a bit in the closet. As you can see, the French have drawn conclusions and decided to change a lot for the better. The new audio does the job. It does not tire, it is soft and pleasant. This is important because the detector should give joy, not fatigue. This is often the last bastion of freedom for many of us. Our couple of hours on the weekend, separated from reality in nature.

IAR (Iron Amplitude Rejection) discrimination and the RELIC program I decided to test on a well-known field with high mineralization and high iron content. First, run and I can’t hear the audio. Nervous situation. Restarts the hardware. In this place, all the equipment sounds beautiful … but not the new DEUS II. It is so stable that I was fooled like a child by a supposedly non-working loudspeaker … For the first 20 minutes, both Mariusz and I are completely surprised. No, we don’t find anything, but that’s not the point. The detector signals target only. Audio flows and multi-technology stabilize the rough ground. How about the performance? Too early to judge.

To make it better, it is All metal and you can also hear iron, although factory muted. The time for real tests will come in the season. Playing at temperatures below zero degrees Celsius is a bit masochistic, but it was worth it. Remember to subscribe and we’ll meet soon.

Posted on Leave a comment

Garrett ACE APEX metal detector – is it worth buying a new canary?

I remember starting my adventure with the Garrett AT PRO metal detector today. It was a total infatuation. For those times, it was a really good detector, despite a number of flaws.

Heavy and ill-balanced, it tired my wrist in an instant. A couple of hours and you really wanted to go home. Experts on the subject say that a defect that occurs on land disappears in the water. There is no buoy effect, displacing the device. Possibly, I wasn’t allowed to wade deep with him. The Baltic Sea is for winter, so I only walked on a wet beach. In addition, the manufacturer for many years completely forgot about the ability to adjust the volume level …. Desperate customers did not agree to this, and in the MAX model, you could already enjoy it!

Many years have passed since then. I’ve never been a fan of Garrett’s ACE series. Popular canaries never interested me. Heavy, without the possibility of ground calibration, audio in the form of a chime for the front door scared me away for many years. Don’t get me wrong, it’s first-contact equipment for many, and I started the shelf higher. I was lucky enough to just be able to afford it.

Adventure with the Garrett ACE APEX metal detector

Garrett’s boisterous announcement of a new multi-frequency metal detector was long overdue. The competition has been using this type of device for many years. I had a lot of doubts about whether the new product from the ACE series called APEX would be really good equipment.

The surprise was big. I just had to revoke everything I’d posted before. Very light, well-made, and very simple. These were the first advantages. It is not waterproof, but the time will come after the premiere of the new AT PRO model. When? Nobody knows that.

Full reference to the layout of the buttons from the previous series is a nod to the most conservative users. Simplicity and more simplicity. It only takes a few minutes to switch over, or a few hours to get to know the device from scratch. It’s not everything. When this detector is turned on, there is complete silence. It is incredibly stable. What remains is the boost feature – the sound of the iron, which is quite controversial for one reason. In a heavily littered area, it significantly extends the reaction time, and in a clean one, it allows you to avoid digging garbage. APEX shines on the beach. We will not dig up any caps … which is not so obvious with other devices, even from the top shelf.

The 11-inch probe, working name Viper, is the best solution. It is strongly narrowed, which shortens the reaction time and allows maneuvering in difficult conditions. I do not see the need to change it to something else, because it will take the whole balance to the head, and the performance will change symbolically.

The ability to walk on a salty beach in the additional MS mode, which mutes and stabilizes the device, is a big advantage. We have one more. This is not even Minelab in the cheaper Vanquish models. Frequency selection. Yes, we can choose. 5, 10, 15, or 20 kHz. This is a great option when the conditions are really volatile and we want to look for specific things.

In addition to the advantages, there are also disadvantages of the APEX detector

The APEX metal detector also has disadvantages. This is a typical general cargo vessel, I would choose something completely different when looking for military, and large ones. It is also only rainproof. You can submerge the probe. Electronics no more. Although she survived a snowstorm at my place, so I can’t really complain. The housing has an internal gasket.

Garrett ACE APEX metal detector – summary

To sum up, the APEX metal detector is a really good and simple device, maybe not the cheapest, but the manufacturer has packed nice, modern electronics inside that can cope quite well in harsh conditions. I buy this product, and you?

 

Posted on Leave a comment

The best Tarsacci MDT 8000 detector revolution in the user’s eye

Half a year ago, if someone had told me that I would get a professional detector like the Tarsacci MDT 8000, I would not have believed it at all … and I did not believe it waiting for a device straight from the USA. I had my doubts standing in the field with him. Now I’m sure. This is the best device I’ve had in my hands for over 10 years … unfortunately, not the cheapest either.

Pros and cons of the detector

I understand there will be two camps here. One says that a good thing must cost money and the other is where you can buy really great equipment for 1/2 the price. Both sides have their reasons, but as we know, the devil is in the details.

Quality workmanship knocks down. No slack, fudge, or complaints … there is one defect of the carbon detector post … apparently, it whistles in the wind … that’s what I read on the Tarsacci forum on Facebook.

Tarsacci Poland:

https://www.facebook.com/groups/363009768484651

Tarsacci UK:

https://www.facebook.com/groups/795633577904679

Everything else is a masterpiece, but it doesn’t surprise me at all. Just check who is responsible for creating this equipment. Dimitar Gargov – former engineer of the Fisher Labs company, which needs no introduction to anyone, like their metal detectors, which are known all over the world. Finally, just add the name and surname: Thomas Dankowski and we have one of the best duos in this field in the world. After over two years of testing and we have the Tarsacci MDT 8000.

Water resistance is a big advantage, but to surprise nowadays, apart from performance, you have to give something else. In this case, we get amazing, soft audio that was created by someone who really dealt with real field research. The sounds do not tire for many hours, they give a precise description of the item and a lot of additional information. When we add above-average performance even with the first 11×9-inch probe, we are shocked. There’s no need to cheat. The Polish icon RUTUS Alter 71 is over 7 to 10 cm shallower in mixed mode, which can be seen in the videos below.

A quick visual comparison of Tarsacci MDT 800 and Rutus Alter 71 in heavy clay soil.

The joy of a professional detector

The popular Boratynka with 30 cm? No problem. Loud and clear, not to be missed. The machine confidently fastens on good objects and gives a descriptive response in the form of sound. Trash and the signature changes, and the sound is longer and blurry. There is no doubt. Here’s an example search video. For several weeks, Mariusz has been unable to get rid of the feeling that he should collect money for this detector. Unfortunately, it is financially out of his reach.

YouTube player

How often to search for metals

In the end, a knockout in a littered area or under the lines. Work stability. There is complete silence. Sometimes I check with a shovel if Tarsacci is still working. Do you have a problem? Is something waking up? You change the operating frequency for your choice: 6.4Khz, 9Khz, 12Khz, and 18Khz. In this way, you can influence the performance or adjust the frequency of work to the prevailing conditions or the items you are looking for. For example, we are interested in big and deep old iron, we use 6.4Khz. We need to take care of ourselves in the trash and look for something small 12 or 18Khz will be a great choice.

The manufacturer spoils us by giving a huge Li-ion battery in the set and a charger, basically two batteries with a capacity of 5000 mAh each. I don’t remember, yet, that it was possible to completely discharge it by going to 9Khz. After 4-5 hours, no line falls, and we still have a supply.

Intuitive operation of the Tarsacci device

The simplicity of use brings to mind devices from the lowest price segment. No drop-down menus or hidden functions or filters that we need to remember about. It’s an amazing advantage. We don’t stand around and rummage through equipment while others dig up stuff.

Flexibility to work in various conditions, from extremely salty beaches to highly mineralized soils, puts Tarsacci at the forefront of the best devices of this type. We have the ability to compensate for volcanic sands and magnetic soils in the form of the BLK (Black Sand) function. We also affect the salinity with the ST settings. And I don’t mean an ocean beach at all… but fields with tons of fertilizers. In this way, apart from the stability mentioned at the beginning, we get peace of mind in the form of no masking from coke or foil. This is a significant advantage over other devices that simply can’t cope in the world.

You can go back to the places you have been to and enjoy them again. In combination with the new 12-inch probe, we get another up to 10 cm more. Finally, the user’s statement:

☘️ Half a year with Tersacci and 2 months with a 12 “coil. I have flown a lot of hours, I think I used 10 batteries and one is enough for a very long time 18 hours at 6.4khz and over 30 at 18khz. There are rather no defects in the construction, the only holes in the seat post howl in the wind ? but they are already wrapped. The traces of wear on the machine are negligible. As for the new coil and without the cover, it seemed to me that it would wear out very quickly, but nothing could be more wrong, only minor scratches came out and that’s it, and the areas were plowed fields, meadows, and stones.

As for the handling, it is very strange because I have not yet met a detector that would be at maximum sensitivity all the time and was so stable ..! As with all detectors, you have to overlap and dig to understand what and where.

Anyone who has doubts and decides that it is just marketing can use the forum where users describe their experiences with this detector in English:

https://www.dankowskidetectors.com/discussions/read.php?2,152652

See you in the field!

Posted on Leave a comment

Tarsacci MDT 8000 another decision

Łukasz Karmalita’s opinion:

☘️ Half a year with Tersacci and 2 months with a 12 “coil. I have flown a lot of hours, I think I used 10 batteries and one is enough for a very long time 18 hours at 6.4khz and over 30 at 18khz. There are rather no defects in the construction, the only holes in the seatpost howl in the wind ? but they are already wrapped. The traces of wear of the machine are negligible. As for the new coil and without the cover, it seemed to me that it would wear out very quickly, but nothing could be more wrong, only minor scratches came out and that’s it, and the areas were plowed fields, meadows and stones.

As for the handling, it is very strange because I have not yet met a detector that would be at maximum sensitivity all the time and was so stable ..! As with all detectors, you have to overlap and dig to understand what and where.

Posted on Leave a comment

An invention that saved many lives

The hand-held mine detector – because that’s what we’re talking about – was invented by Józef Kosacki in 1941. The prototype was built in just three months, and then quickly went into serial production to “significantly contribute to the Allies winning World War II”.

Even King George VI sent a congratulatory letter to Kosacki in recognition of his merits, and yet few people know about the Polish inventor today. Just like the circumstances of the creation of the prototype.

And it all started with a tragedy. On June 1, 1941, a team of several people from the then-famous 10th Armored Cavalry Brigade was sent to comb the Scottish beach near Arbroath. A routine patrol hit the coast, which, however, had been mined before the British – for fear of German landings. But no one knew about the mines. None of the Polish soldiers returned from the mission, which shocked both British and Polish commanders. One of them was Lieutenant Józef Kosacki, who quickly decided to return to the idea he had been working on in pre-war Poland.

The starting point for Kosacki was the discovery that telegraph amplifiers react with hum to the presence of metal. That is why he used this phenomenon by constructing a mine detector – he worked on the prototype for only three months, using the phenomenon of the electromagnetic field.

What did his detector look like?

“It was light, weighed about 14 kg, and at the same time relatively simple, possible to be carried and used by one soldier” – remind Teresa Kowalik and Przemysław Słowiński in the book “Royal gift. What Poland and Poles gave to the world”. It consisted of a wooden satchel with an acoustic frequency oscillator, an amplifier, and power batteries – put on the back. And also from a bamboo stick with coils and a variometer (it’s nothing more than an inductance changer). Small, uncomplicated, and handy (“earlier devices were not suitable for use on the battlefield. They could help engineering services clearing a battlefield, but not soldiers breaking through a minefield”). And most importantly: very effective.

A handful of 1p coins were scattered on the beach. The task was to find them all. The competition, which was announced by the British Ministry just a few days after the tragic events near Arbroath, had 7 applicants. The winner turned out to be Kosacki – his detector tracked all the coins. Very quickly, thus outclassing the competition.

The device received the official name “Mine Detector, Polish Type No. 1” and quickly went into serial production. Then it entered the equipment of the British army, and over time it was used by other allied armies. The detector was used for the first time in the Second Battle of El Alamein in 1942, where it significantly contributed to the Allied victory.

“In the following years, improved and modified, the mine detector found its way to battlefields around the world. Simple, yet effective, it turned out to be extremely long-lived equipment – it was used until the 1990s, of course in a modified version. The number of people saved by it can be estimated in thousands.” That is why today Kosacki is most often referred to as “the man who contributed to winning World War II”. Or shorter: “Pole who stopped death”.

Posted on Leave a comment

Tarsacci MDT 8000

Another few interesting finds from a passing spot with Tarsacci MDT 8000.

Grapeshot ball
50 groszy aluminum post communist times…
They are waiting for us in sleep…
Posted on Leave a comment

Nokta Makro INVENIO PRO 3D visualization of objects hidden in the soil

Invenio Nokta Makro INVENIO PRO allows you to show the shape, dimensions, depth of deposition, and the type of metal from which the object is made.