Posted on 2 Comments

Minelab Manticore and Multi IQ+ technology

The first outing with Minelab Manticore was not successful. I had considerable doubts. After all, the price is about 10 thousand. PLN does its job and we have above-average expectations. The detector frighteningly distorted the color and no change and raising the iron limits (FERROUS LIMITS), or lowering the sensitivity and ground calibration did anything. I was stuck. I tried various ways to deal with the change in reactivity and frequent detuning, but it did not bring the expected results. The device was unstable and it was difficult to figure out what was the correct signal from the target, and what was ground interference and color-distorting iron.

Yes, the place is very difficult, and not because of the soil, which is easy and sandy, but because of the amount of iron in it. Minelab Manticore requires a bit more knowledge and experience from the user than devices from the lower price range. Here you have to think hard about what program we will choose for the prevailing conditions and how we will set it. In my case, I decided to change the program from a FAST setting to LOW CONDUCTORS. So low guides. Why? Old and fine silver has a very low ID and is located right next to iron.

The next step was to determine the iron ranges (FERROUS LIMITS), here the matter is not so simple. Low value more color distortion but less masking. I decided to set the upper value for fine iron – such as nails – to 6. This is slightly less than factory 7. The extreme version is 4, but I do not recommend it at the beginning, maybe when you get used to the equipment. It gives amazing results.

Recovery speed is a parameter responsible for the separation. Here I stayed with factory 5, and sometimes I use 6 in a place with more traffic 😉 Higher value, better separation of objects and more stability, less range. At low values, you have to sweep slower and the equipment becomes less stable. Fortunately, we can influence this with the speed of the sweep. When we come across a garbage can – we slow down, and when it’s clean we can easily speed up. Patience and experience, humility, and there will be results!

It remains to set the sensitivity. The principle is always the same as in other detectors. We go up and watch how the detector behaves. Unstable work, we have to go down. Along the way, we do NOISE CANCEL, i.e. scanning channels to look for the best one. We can combine this with the sensitivity adjustment and choose the right setting. It is worth holding the interference reset button longer until you get one repeatable channel after each scan. In the case of Manitcor, the algorithm analyzes the interference and selects the best channel for the given operating frequencies selected with the program.

Audio. What audio to choose in a place where iron and its natural oxidation make even shallow objects practically inaudible?! I chose the ENHANCED option with noise reduction and it was a hit. Finally, the number of tones. It has been known for a long time that simple audio is the best in a dump or among the iron. One ton fell. Modulation? I chose SIMPLE, which is the smallest difference between a strong and a weak signal. Why? A large value for the MEDIUM or RICH parameter makes it easy to get lost with a large number of different signals, especially high tones from piercing iron. We want to check every signal and not miss anything!

Ground calibration remained at 0, although tracking did not introduce significant changes. The maximum corrected value is 2. The device cannot be manually adjusted by the pumping process here – too much iron!

Let’s go back to the results obtained, and this one completely knocked me off my feet! The spot I passed through revived and began to produce signals that were previously inaudible to other devices, and I spent almost two years in this place! It’s a strange feeling to pull stuff next to your pits and footprints … MultiIQ+ software Minelab does the job in combination with very fast hardware. The sensation is shocking when the detector separates the masked signals with the iron and the 2D graph becomes a checking tool. How to do it? The matter is simple because it is very easy to distinguish interference from iron and ground in the ENHANCED audio. In case of additional doubts, we look at the chart and rotate over the target by 90 degrees. In this case, after rotation, the TARGET TRACE signal in the conductivity axis, signaling the so-called color returns to iron. The chart gives us amazing opportunities to check the signal. For example, it shows large iron objects masking low conductors, small iron showing color, but also a pair of different objects next to each other. The dominant of the stronger signal changes with the change of position over the object. It’s just brilliant! If we add interference, mineralization, and different types of conductivity, we have a full picture of the possibilities!

YouTube player

Finally, is the detector worth 10,000? zloty? Certainly not in this country. We simply cannot afford it and no matter how good the ratio of our earnings to price is, it is unacceptable. Too bad no one talks about it!

Judge for yourself and remember to comment on this article and on our social media.

 

Posted on Leave a comment

The revolution that is not coming

I have a strange feeling that the world of metal detectors is stuck at a certain point. We have been waiting for spectacular changes for years and they are not coming… maybe they are coming differently, but on a different scale than we expected.

Minelab Manticore or XP DEUS II are really good devices, but do they bring anything groundbreaking apart from the dose of well-known solutions?

Certainly, SMF devices are better than what we know from the past, but they are also not without their flaws. The advantages include stable operation in more difficult conditions and better ID compared to single-frequency devices. More accurate signaling of objects from both ends of the scale – low and high conductors. This makes detection easier. This makes detection easier, e.g. old and fine silver is the beginning of the scale close to iron, while large is its other end in SMF, it works really well.

What disadvantages? Less resistance to EMI interference – after all, we work in a wider frequency range and slightly worse performance when it comes to depth.

In my case, I always choose an advantage in the form of better identification and separation in iron, and this can be different, opinions are divided here.

It must be remembered that such a Nexus MPV3 is completely immune to EMI interference, which makes it much deeper and, after adding the adaptive speed of separating the target, insurmountable … unfortunately, you have to pay for it and it is a device for conscious detectorists. It is not light and consumes 10 AA batteries in a short time. Something for something as they say.

We also have the Tarsacci MDT 8000 with hybrid PI and VLF technology. A mix of pulse device performance and VLF discrimination. The detector is really deep and works great in iron or with magnetic stones. Unfortunately, target signaling and its interpretation is no more difficult than in VLF and SMF devices.

It’s better, multi-frequency detectors are more stable. Such a good old Whites Spectra, using three frequencies, is much shallower and very susceptible to interference. It will not separate as well, especially in iron. In addition, under high-voltage lines, there is no chance and nothing will change it, no change of settings.

It remains to wait and watch what the next years will bring, I know that it will be interesting, that’s for sure.

Posted on Leave a comment

Nokta Makro The Legend pairing problem with BT headphones

After updating the software to 1.09 and updating the Bluetooth module, the detector does not see the factory wireless headphones. What should I do? First, press the mode button and the upper side button from the volume control (the place where the sticker with the subtitles and the flashing LED is located), after 3 seconds you will hear two silent signals. The headphones are unpaired.

Then the detector, set the BT icon to 1 plus press the pinpoint button until the letters: FD appears on the screen. Then all headphones were unpaired. We are waiting for it to connect, if not, turn off both devices and turn them on again!

Remember our social media on Facebook, Instagram, YouTube, and Twitter. Also, leave us a review on GOOGLE.

Posted on Leave a comment

Minelab Equinox 700 and 900 the fish rots from the head

Has become. Minelab announced new models… Equinox 700 and 900. That’s how they did it… they refreshed the line. So what do we get and how is the new model different?!

A flashlight has arrived, vibrations, a wider ID scale, improved ergonomics, a scale for iron from -1 to 0, and for higher conductors from 1 to 99. They went crazy.

Looking soberly, the changes are cosmetic beyond the scale, but how about the price, in our country, it is the dominant factor. Let’s see what the difference is … GBP 799 for the 700 version and GBP 1099 for the 900 version. This means at the current exchange rate of PLN 4354 and PLN 5989 net …

To sum up, PLN 5,356 and PLN 7,367. Is it supposed to be an alternative to the almost PLN 10,000 Manticore and a response to the fans of the brand who said that someone exaggerated the price? This is how the mouth closes efficiently. Pure marketing. You can not afford it?! Buy yourself a cheaper one… see what we have prepared for you. A slight facelift and refreshed device can be yours.

How does the price compare to the competition? The answer is simple. Miserably. It’s cheaper than Manticore but still expensive. Adding a few goodies won’t make us justify 20% more. There is no chance, although the manufacturer was based on this assumption.

Maybe it’s a matter of prejudice, but Equinox has never convinced me and many of my colleagues feel the same way. After a year of use, I got rid of the device without much regret. It is possible that it was a mistake, but compared to the old XP DEUS model, Whites Spectra or decent DeepTech analogs, I did not see any greater depth, better identification, or stable work.

It is possible that the new models are much better, but I see no reason to be interested in them. Whether this is a mistake time will tell.

Coming back to the prices, well, we live in such no other conditions and only a few can afford expensive devices above PLN 2,500. It is worth remembering and reminding each time because it is not the individual who indicates the goal, but the majority.

Posted on Leave a comment

Depth or separation?

Depth or separation? The eternal question and sleepless nights. I choose to separate objects because this is the most crucial thing in the places where I am able to search. The race for a few inches leads to nothing constructive, but the ability to see in iron does. Scrap heavily masks targets, and it’s not big objects and nails, but also decay dust – its condensed oxides!

The electronics of the detector have to process a lot of signals in a moment, and if we add other conductors to this, the time to generate a signal is very short. Larger signals effectively cover the response of small objects – higher conductors.

The level of mineralization of the substrate, the sweep angle, the conduct of the probe, and the frequency of work are important. All this has a dramatic effect on the effects. Wrongly selected detector and incorrectly set, and there is no chance for any effects. I have experienced this many times and it was very painful. A change in approach, improved probe guidance, and higher operating frequency, and we begin to hear signals previously unavailable.

So what is my recipe for a lot of iron? It depends on many parameters, but to simplify … a higher separation speed of the so-called recovery speed, higher operating frequency, lower sensitivity to conditions, and lower discrimination. Slower sweep, still parallels to the ground. You can also raise the probe slightly up … so if we are fighting with large disturbances from the ground. It will be shallower this way, but we will hear objects that we had no idea about before.

Finally, you can use a single high-frequency operation, an adaptive refresh rate device (Nexus MP V3), or a hybrid PI/VLF detector (Tarsacci MDT), but who can afford that?!

You can find more on this BLOG and on YouTube and social media on Facebook. Speak soon. Comment under the article.

Posted on Leave a comment

The Nexus is a completely different detector

Nexus MPv3 is a detector so different from currently presented detectors that it is difficult to compare them directly. Expensive, heavy, and difficult to use, but perfectly made. Worth every penny for me, but obviously not for everyone.

Why is it worth spending a fortune? First of all, you need to have a lot of experience, a small ego, a lot of humility, and patience. Success requires hard work, only then it tastes the best.

MPv3 is in a completely different league when it comes to performance. No known hardware comes within a meter of the Nexus. Does this mean that it is the best equipment in the world? No. Perfect for old places, but expensive and requiring full understanding.

In addition to the depth of detection, we get beautiful analog audio and a guide signal closely related to the ground calibration, giving a full description of what is happening under the probe. Pure analog power packed into ten…yes ten AA batteries.

Nexus opens old spots and helps close new ones to the end. The whole thing makes a hell of a good tool. Modulated VCO-type audio, depending on the settings, allows you to favor particular conductors. The VCO LED indicator works in a similar way. It’s also adjustable. We have a pair of colors for each guide from green, to orange, blue, and white. It’s a big simplification.

The combination of all these possibilities results in a devilishly effective device, although demanding, but also quite forgiving of mistakes. Perfect second detector for me.

You will find out more soon. Remember about our social media and YouTube channel.

Posted on Leave a comment

Nexus Standard MP V3

Nexus Standard MPv3 is the next incarnation of the metal detector of the already famous manufacturer. Georgi is a true genius, no doubt about it.

The new detector is not for everyone and not because of its price. It’s all about service and understanding and taking the time. It’s a very difficult device. This is IB (Induction Balance) technology.

The IB metal detector is capable of discriminating between different types of metal objects, such as bottle caps and coins, by distinguishing the amplitude of the corresponding reception signals. In addition, the detector is equipped with a tuning adjustment, which is used to eliminate the influence of ground disturbances with a high content of iron and mineralization.

So in a nutshell and strongly simplified. What does it give? Ability to work in an environment with a lot of iron and mineralization of the substrate!

Unfortunately, this requires a lot of knowledge and awareness from the operator to fully understand the machine. Time and experience plus humility and focus. There is no other way. One mistake in the settings and the whole intricately arranged house of cards collapses.

Nexus Standard MPv3 is a typical knob, where the role of identification is taken over by a multi-color LED display. In addition to additional audio, we have a VCO-type selection knob, discrimination, coarse and fine ground calibration, and mineralization switch … there is a bit of it and it’s not easy to get the hang of it. I am full of optimism and the producer gave me full support. Remember to subscribe. It’s time to face this beast. We’ll see how I do. Courage is added by the fact that the set includes a double probe 2x 10 inches, the so-called low-frequency butterfly, which is supposed to translate into depths unattainable for other devices known to me. We’ll see.

Below is a description of the functions and calibration showing how complicated this device is.

Ground calibration. GB in the MP V3 is divided into two knobs – GB Fine and GB Coarse. The fine adjustment is 10 turns for fine-tuning, and the coarse adjustment is one turn for coarse tuning.
To adjust the ground balance, turn both GB knobs to position 10 clockwise. While moving the probe up and down, rotate the Coarse GB counterclockwise until the detector generates a soft signal as the probe descends.
Then tune with GB Fine by turning it counterclockwise. Continue fine-tuning GB in the final phase only with the help of GB Fine.

You can also do GB in reverse order. Turn both knobs to 0, fully counterclockwise. Then adjust GB Coarse until you get a soft signal as the probe goes up, then adjust GB Fine. The MP V3 Discrimination Control needs to be set somewhere around 3-4 on the scale (similar to the MkII) to avoid iron digging. It is best to select the setting on-site after checking several signals.

Unlike the MkII, the MP V3’s discrimination is very soft and forgiving, meaning there is no danger of clipping too much, everything is done in very small steps.

The LC-MC SET knob is used to turn the RGB LED meter on/off and to adjust the cutoff point between the low (LC) and mid (MC) leads. If this control is set to the left (0), only the lowest conductors will be colored green – hand-minted gold coins, Roman gold coins, any small gold coin or artifact, and very small pieces of foil.

All other non-ferrous objects will be marked with either orange (medium MC conductors) or white/blue (high conductors). If you turn the LC-MC SET to the right, some
hand-minted silver coins will be marked low guides as well as most lugs.

Mineral Control can only be used on highly mineralized soil containing magnetite. MC Fine stands for precise regulation of mineralization. The sensitivity of the detector will be slightly reduced, but this will allow you to reach the audible threshold of objects near strong sources of interference caused by mineralization.

The leading signal the threshold in the MP V3 should be set to the minimum audible level at all times like a constant, stable hum so that the deepest small objects can be detected and all others give a really good sure response.
This setup will ensure that the V3 performs far better than any other detector in existence, even the MP V2 (which is a beast in its own right).

The VCO setting is only intended to be used to identify uncertain, deep objects in the cluttered ground. The VCO should be set so that the first green LED just lights up. This will adjust the VCO tones to an audible level between lows and highs.

VCO is the best way to identify very uncertain (weak signals) targets at maximum depth. When searching in the cluttered ground, the guide signal needs to be quiet so that constant use of the VCO audio is not a nuisance.

If you get your hands on one of the 11.5-inch CC probes, you’ll find that the V3 in VCO mode is unbeatable in iron-strewn areas. No digital detectors can come within a mile of what this V3 detector can do with the right probe, according to the manufacturer. We’ll see!

The general advice is to keep the search coil approximately 10 cm off the ground at all locations and maintain a stable guiding signal. Once the target is located, if uncertain, lower the search coil closer to the ground. If the LED meter shows nothing, use the audio VCO to check the target.

Iron will not be indicated on the RGB LED meter unless the discrimination control is set to a value close to 0. In this case, iron will be indicated green as all other low conductors.

The battery test will show levels from 10.5V to 11.5V. So, when the battery test shows less than a full green LED bar, it means the batteries are nearing full discharge.

Posted on Leave a comment

EMI interference

What is EMI Interference? The definition is quite broad and a bit confusing for non-technical people:

Electromagnetic Interference (EMI) is any signal or radiated into space or transmitted through power or signal lines that threaten the operation of radio navigation or other safety services, or seriously degrades, blocks, or repeatedly interrupts licensed radio communications. Radio communication services include, but are not limited to, television and radio broadcasting, mobile telephony services, radar scanning, air traffic control, paging services (pagers), and PCS (Personal Communication Services). Licensed radio services, such as those used in WLAN networks or Bluetooth technology, together with incidental transmitters, such as digital devices including computer systems, contribute to the electromagnetic environment.

In our case, these are simply interferences that make the work of the metal detector difficult or even impossible. Half the trouble is when the process is visible and the device characteristically excites, generating a target signal and a numerical ID. Then we know that we are dealing with them and can take appropriate measures. What? Detuning the so-called changing the channel, reducing the sensitivity, or choosing a different operating frequency, if possible, direct elimination of interference sources such as telephones, transmitters, electric fences for animals, etc.

In difficult cases, you can use discrimination and cut-out interference, but this is only a half-measure. We lose performance, which is already heavily limited by EMI interference. A colleague who accompanies us can effectively deprive us of the chance to find finds, being even several meters away with his detector! Don’t fall for the group search, it’s just a nice time at the rally, you can’t count on the effects in such conditions. It’s unlikely!

What was the better situation, and what is the worse? Quiet disturbances. The ones that are not visible, and everything seems to be ok. We lose performance, but the detector does not signal it in any way. You can put a coin under the probe and the device can be completely blind. How to defend against it? It depends on many different factors, and above all on the type of device we have.

We preventively check other programs and detune the device from time to time. We check the signals with the person next to us to see if our detector can handle them as well. It’s the only option. SMF-type machines – simply put, multi-frequency machines, usually work in two or more frequencies, processed by software. In some cases, it may turn out that what was supposed to be a great advantage of a wide frequency range becomes a disadvantage!

For example, we have a program working in the range from 5 to 40 kHz – ideal for searching for gold, i.e. a low conductor is allergic to high frequency, and silver – a high conductor to low frequency. In addition, high frequency copes with small things better and with greater mineralization of the ground. In the case of low frequency, objects with a larger volume are signaled better. Story. We will not miss anything from what interests us the most!

Unfortunately, right now our greatest enemy is approaching and eliminating one of our frequencies. Without seeing it, we lose 50% of the possibilities without knowing it. Often programming and filters sewn in with it additionally stabilize the work of the detector. For this reason, the prevention described above is important. In this way, we will avoid erroneous opinions about the equipment and unreliable tests, especially from the test tracks. Interference can confuse us, so it is worth spending many hours checking different variants of settings in the field in various conditions!

Remember to comment under this article and on our social media.

YouTube player
Posted on Leave a comment

XP with panel or without?

The question is simple with or without a panel? ORX, DEUS, and DEUS II are available in the lite version, where the control electronics are replaced by wireless headphones, also with buttons and a display. So which set to choose? Logically, the best and full, unfortunately, the price difference is significant, and on the other hand, you have to pay more later to buy a panel. It is bad either way. So what decision to make?!

If it is to be the first detector, then we can safely give up this add-on. Why? For a simple reason, we have to go by ear and we don’t have a display with ID numbers or a graph. We learn organoleptically from scratch as it should be – that is, by ear! It only pays off and increases our skills. Such mastery of the equipment gives you a lot and allows you to avoid mistakes at the beginning of the road. The second plus is not wasting time on moving the device when we do not fully understand certain functions and dependencies – less chance for wrong setting and skipping items. Finally, the last thing is weight loss, we can live knowing that our equipment is the lightest in the world!

Are you advanced and want to update? Buy yourself a panel, this solution is for you! There is one more option to work with the equipment, first listening and then verification on the chart. That’s how some programs work, and it works.

We have experience and we understand how the detectors work, then the panel is a chance to squeeze out additional possibilities, change the audio or precisely adjust it to the conditions or your own preferences.

Posted on Leave a comment

The silent killer

There are days when all the monotony is dazzling. And this time it happened. A narrow strip of land, your own buried holes, footprints, and… bang! Signals appear coin by coin. Not that immediately some spectacular silverware. Popularity, but what satisfaction!

One clear thing came to me that has been bothering me for a long time, but let’s start from the very beginning. The premiere of XP Deus II and Nokta Makro The Legend, a number of videos and opinions, and in addition strongly divergent. I own both devices myself, so I started testing. It’s a bad time of year. Summer. Hot and a lot of UV radiation, which, as we know, negatively affects the probes. One place and still the same effect. The work is stable for a while, and then it is difficult to master the device. It does not indicate interference, only the ID jumps, it is difficult to track the target, and the identification scale closes from start to finish. Then I put it down to UV and temperature, and in part it certainly was, but I didn’t take into account the biggest problem of SMF technology … EMI interference, and the quiet ones that you can’t see.

In a regular VLF device, one frequency is easier to manage in terms of external interference, we can see more and we have more control. In the case of a multi-frequency and, moreover, simultaneous device, no longer.

For example, to put it simply, if the device uses two frequencies and one of them is disturbed and simply does not work, we have no chance for correct identification, tracking, and signaling of the target, and the depth performance can be forgotten.

A typical example from my tests is a Minelab Equinox 800 under two parallel high-voltage lines. Quiet and stable and at the same time 5 cm shallow!

The same thing happened to me with Deus II and The Legend. Hence the opinions on the Internet that the equipment does not work and sucks. Mistake! It’s EMI interference. How can you get rid of them and what can be done to make working with the SMF detector problem-free?

We start with detuning from interference (scanning is usually automatic). It is worth carrying out this process from time to time just in case. The next step is sensitivity, we go down to the level of stable operation of the detector and lack of interference, and excitation. All freaks twisting to the max will die in this place. The target’s signal will not cut through the interference. It’s like driving a car with a high beam in the fog. Suicide. The ground calibration, was corrected and checked. You can find how to do it on my YouTube channel.

How to verify? There is a method for this, apart from effective and stable work and a handful of coins in your pocket, you can use the so-called leading signal threshold. Stable means the detector is operating smoothly and the signal is set correctly.

you don’t believe? Video below of a man running XP on Deus I alongside Deus II. After this maneuver, the last version does not signal the coin in audio. After detuning, the coin signal is back!

YouTube player
Posted on Leave a comment

Great Trinity

Five months of intensive field testing with us. The area is 6000 m². Three devices: Tarsacci MDT 8000, XP DEUS II, and Nokta Makro The Legend. Changeable weather conditions, but as in summer, the temperature is around 23 to 30 degrees Celsius. For the DEUS II and The Legend detectors, UV radiation and general heat had a terrible effect on performance. I don’t know if it’s a matter of SMF technology, but both devices lose a lot in such conditions. This manifests itself in unstable work and difficulty in finding a goal. In the case of the Tarsacci detector, which is a hybrid device, i.e. a bit of VLF and a bit of PI, there is no such problem. The probe doesn’t drift and doesn’t go out of tune.

Soil conditions were difficult not because of the soil itself, which is sandy, but because of the high iron content in the form of post-settlement dust, nails, and pieces of pottery and rubble. Modern garbage was rare in this place.

Tarsacci takes time and understanding to set up and master, it’s a bit better with XP DEUS II and The Legend. The last two machines are more forgiving and have better target signaling and locking. Simply put, these goals are easier to extract in difficult conditions.

Hybrid technology means less masking and greater depth of detection, and you can feel it right away. Stable operation unattainable for SMF-type detectors (although stable anyway) translates into greater comfort of searching, giving a longer time and the majority of finds. The MDT 8000 is the kind of equipment that you either love or hate.

In the case of XP, we have a lot more options to choose from. The sound and ergonomics mean that you don’t want to let this pipe out of your hand. After taking the time to master the settings, it is a great detector to work in technically difficult terrain, with a lot of configuration options.

The Legend is as deep as XP DEUS II and can be deeper and more convincing at times. The price is an argument, but the last update 1.09 did its job, and having the same amount to choose from in the case of the XP product, I would seriously consider it. Nothing can beat ergonomics, but everything else can become conventional in this case.

The Turkish manufacturer has made amazing progress and now it is possible to shell coins near the iron, which was not so obvious before! Filters with adjustable speed recovery speed allow you to separate difficult targets better and faster. The device does the job, and in combination with the new audio, it works really great. Personally, I go with the two-tone mode, but Pitch or 60 tones are also alternatives. The 6” probe included in the PRO PACK set is the perfect panacea for a trash can and, together with the low weight, compensates for the fact that we have to swing a lot more with such a small disc! Such a set means that there are not several objects under the probe at once and it is easier to track the right target.

In normal conditions, without the old iron, Nokta and XP perform really well and are not inferior to the Tarsacci. The fun begins only in difficult conditions when coins pop out from under the iron. Then it gets hot. Every Seeker knows this condition well…

Posted on Leave a comment

Nokta Makro The Legend real SMF

The Collins Dictionary defines the word “legend” as follows: When you refer to someone as a legend, it means that they are very famous and admired by many people. That’s a definition that certainly includes the Nokta metal detector – it means both famous and universally admired.

There are multi-frequency (MF) detectors and there are simultaneous multi-frequency (SMF) detectors. Both have their followers, so which is best? It depends entirely on where you regularly look and how you look, not forgetting other aspects of fun. These will include consideration of after-sales support, accessories such as probes, warranty repairs, and even dealer reputation.

MF detectors offer operators a range of frequencies from 4kHz to 81kHz, depending on make and model. What MFs don’t do is generate multiple frequencies at once, unlike SMF. Because MFs transmit one selected frequency at a time, their electronic target analysis systems are less complex and therefore less expensive to manufacture. This is usually reflected in their much lower price. Many seasoned MF aficionados prefer to tune their detectors to the frequency that best suits the type of target they are looking for… eg gold, minted silver, copper, and even iron objects.

Nokta Legend is a real SMF that transmits 4kHz, 10kHz, 15kHz, 20kHz, and 40kHz synchronously. Why? Straight. SMF is a catch-all system. Lower frequencies penetrate deeper into the ground/wet sand, while higher frequencies – although slightly less so – are more sensitive to small gold objects. A single MF frequency option is also available to the user.

At a price of around PLN 3,835 along with “promotional offers” that include additional probes and other accessories, it is hardly surprising that the Legend is so highly regarded. Don’t be fooled, this is a technologically advanced detector with features usually only available on the market for detectors worth over PLN 7,000. What makes it stand out is that it has an average price.

From a commercial point of view, it’s a damn strong mix. Nokta placed the Legend electronics in the same housing as the Simplex+ model. The build quality and architecture are typical of a Turkish manufacturer. The model is solid and based on the experience gained in the production of other detectors. As sailors say about yachts: “If it looks good, it will sail well.”

Where we have garbage and iron, a small probe should be used, and anyone who searches the shoreline knows what I’m talking about. Beach seekers often avoid cluttered areas like the plague. Other tough guys work in these conditions, pushing the capabilities of their devices to the limit.

Large-diameter probes are not my ideal choice in cluttered areas, due to one major disadvantage: vulnerability to “target masking”. In the case where we have two objects – one garbage and the other, e.g. a gold ring – both entering the field of work, and the garbage object is often the stronger signal of the two and “masks” gold. Some areas were not only loaded to the brim with garbage and all sorts of metal objects but also lost jewelry. Not surprisingly, these places are almost impossible to search with large-diameter probes, and I mean the 11-inch Legend probe as well. As you might expect, many Seekers steer clear of littered areas. The key to unlocking the loot is a probe with a small diameter of no more than six inches. The likelihood of two targets falling into the small diameter of a small probe is much less likely.

I hope the 6-inch NM probe (LG15) will stand out, as does the elliptical 9.5″x5″ (SP24) used in my Simplex+.

It’s obvious that electronics and water are a poor combination. So, if you’re taking your expensive metal detector anywhere near water, especially salt water, it needs to be waterproof to survive accidental submersion. The Legend is fully resistant up to three meters. For diving maniacs, you can buy headphones for diving on a cable. Same as Simplex+.

Posted on Leave a comment

Tracking or not Tracking?

Ground calibration is the basis for ensuring the detector’s operation in difficult conditions, it can be carried out manually or automatically. There is still Tracking, i.e. the function of continuous ground tracking.

Good on clean substrates where mineralization often changes over a short period of time. There is also a downside, false signals can be caught, and objects will need to be swept several times to generate the correct signal. Tracking can get completely lost on magnetic stones or with a lot of ceramics and iron. Large clutter also makes things difficult, it’s all a matter of work algorithms and accompanying filters. Values can be averaged and this is where false signals appear.

Manual tuning gives the greatest guarantee that the metal detector is properly calibrated to the ground. Unfortunately, there are also places where the amount of iron makes it difficult to calibrate manually and automatically, and then it is worth starting Tracking … just do it wisely.

We look at the values and if one value is scrolling all the time, just disable the ground tracking. Ready! We have the value we were looking for. The machine did it for us! It remains to check it from time to time. How? Simply pump the search coil over a clear spot, if the signal changes or you hear an excessive response from the ground, re-tune.

Good positioning is crucial for stable operation and proper signal for a given object and decent depth, and we must remember this every time.

Posted on Leave a comment

How foil masks signals

A great demonstration of how foil, magnetic stones can mask signals. So is iron. Comparison of XP ORX and Tarsacci MDT 8000. Enjoy watching.

YouTube player
Posted on Leave a comment

Tarsacci MDT 8000 REX!

Different technology and completely different possibilities, but only in the right place is the advantage of the Tarsacci MDT 8000 detector that crushes the competition! You do not believe it? Marketing gibberish? Read foreign forums, especially from the USA… these are only the best opinions, but there are also disadvantages.

This equipment, like any other, requires some time and understanding, it is not a low-end, plug-and-forget model. It takes some time, but the results speak for themselves. There is one more little snag. Tarsacci MDT 8000 metal extractor in ordinary conditions, such as low soil mineralization or lack of coke, iron, and foil, will not show anything spectacular. Yes. You need a place full of iron, pottery, coke, slag, magnetic stones, and similar crap, and that’s where the real fun begins! I’m fucking stupid?! Does he probably want to sell…?! Nothing like that, a couple of weeks in the same place over and over again following my footsteps. In addition, various other competition equipment, change of operators, weather, and an area untouched by human hands for 40 years. Only mowed grass. Even changing the orientation of walking in your footsteps, digging on old holes – your holes (fenced area)!

Effect? Pulp! Shock and amazement. The results speak for themselves, competing detectors on various programs are 3 to 5 coins and Tarsacci?! Twice as much and always in the same place!
Recent searches and only this detector give advice. Space and departure at the same time! How is it possible that a silver coin can be heard from over 30 cm under the layer of iron, nails, and ceramics? Two other devices signal nothing but iron, or operate at the limit, although they are perfectly aligned, they have a clear problem. The probes begin to drift and iron wraps around the scale, pottery and stone beat in the middle. A spooky overture, no chance against the cacophony of machine gun sounds!

Hybrid technology allows you to see through this iron to some extent. Vulnerability to camouflage items is less. It’s not 100% known, but it’s still better than the latest top-shelf metal detectors. It makes a big difference and it really works!

Posted on Leave a comment

Minelab Equinox vs Tarsacci MDT coin conglomerate

As you can see in the video below, Minelab lays out such a goal as a conglomerate of coins. It’s a difficult goal. Tarsacci is being tested.

YouTube player
Posted on Leave a comment

Whites Spectra uncompromising detector

Whites Spectra is a unique metal detector. Complicated to use at first glance, but giving amazing configuration options. Why is it so special?

Firstly, it is a detector working in three frequencies at once, and secondly, it has a mixed mode, not like the RUTUS in the mono version, but a stereophonic one. What does it give? Both static and dynamic channels work simultaneously and are not switched between each other as happens in the mono version. We hear all the time about the multiplicity of depth and types of targets. It’s hard to miss items and we know what we have under the probe. This is a great comfort of work and if we add to it great identification, this device, despite its age and not very high speed of object separation, is still an unsurpassed model for many manufacturers.

There are also disadvantages, apart from the above-mentioned complication, the weight of the entire device and the color display are not very visible in direct sunlight. It is true that the Sharps LCD has great contrast and good backlighting, but it will not be at the level that black and white screens give.

Another problem is the power source. Factory batteries last literally for a while and are a pain to use and charge. Much better to switch to a pack of 18650 lithium-ion cells (3 pcs.) and an electronic charger. I use such a set myself and the working time is three times longer. I bought a basket for three such cells and designed and printed the housing.

The factory seat post is also not the most comfortable, but you can easily adjust something lighter.

The work itself and the ability to configure after each other give virtually unlimited possibilities. The initial learning about the equipment, it requires a lot of patience and perseverance as well as knowledge of the English language. Dedicating a few months to learning pays off in the field in the form of better identification, easier fastening on the target, and not tiring work. Fewer random sounds are also a big plus.

The ability to configure allows you to adapt to many scenarios and types of searched objects. The separation of software and hardware settings as well as filters allows you to configure the detector for yourself also in terms of audio or displayed ID and pictograms and ending with colors. This is something unheard of nowadays.

The V3i version allows you to use the XY plot option for additional item identification. We see as many as 3 frequencies in a graphic form, which allows you to better determine the conductivity and type of metal in some approximation. Even XP has used this in the XP DEUS I and DEUS II models.

The last thing is the depth indicator. Not as graphic as we know it now, but in cm and all the time in a dynamic mode without the need to track how it was done on other devices. In this simple way, we can distinguish what is surface garbage and what is a valuable item lying much deeper.

Bob Canaday, the late creator of the Whites Spectra, was undoubtedly a genius, and it’s a pity that none of the current metal detector companies have undertaken to continue his legacy.

Posted on Leave a comment

DeepTech Vista Gold Hound is really worth it

DeepTech replaces Tesoro in the production of typical knob metal detectors. While the build quality of the US manufacturer was higher, the electronics and its work are definitely better on the side of the Bulgarian manufacturer.

The latest Vista Gold Hound model is a traditional two-tone detector with the added threshold function. The device is fabulously simple and convenient to use. Low iron tone, high color.

It doesn’t take much time, just turn it on and everything becomes easy. We start with setting a stable level of sensitivity, and ground calibration, and end with adjusting the threshold, which is actually an additional filter that stabilizes the work and allows you to suppress ground disturbances or, on the other hand, strengthen the ghost signals.

Gold Hound works at 30 kHz and is extremely stable. No crackling, squeaking, or false response from the soil. It really makes a big impression. Two simple signals and we know everything.

I had the opportunity to compare it with other detectors in a place with high mineralization and a huge amount of iron. Gold Hound reigns in terms of working comfort. It is stable and the signals are clear and sure, no dilemma about whether to dig or not. It fastens perfectly on the targets and gives additional information in the form of a low tone if we are dealing with corrosion. The break signal is not uniform and changes over time, it can also be quieter and give a distortion effect for very deep objects.

There are also disadvantages. No double discrimination makes us dig every color. This is a big plus, we won’t miss anything, unfortunately, it’s a problem in a large dumpster. In this case, DeepTech Vista X has the advantage of double discrimination, of which we can be sure to some extent.

Another problem is the frequency of operation … the device is really one of the deepest that we have working at 30 kHz and to such an extent that it can easily compete with 14 kHz! Yes! High mineralization and iron are not a problem, but clutter and small, thin plaques are. They strike like big coins and there is no difference in audio.

On a good spot, this detector is real gold, thin silver coins that most high-end toys do not signal. No problem! Vista Gold Hound will separate even the most masked objects in the area of rusty nails.

For extreme places, you can buy a SuperSix probe. This small sniper rifle, as the name suggests, will allow you to reach difficult places, with such iron condensation, where other detectors simply cannot process signals.

Remember to subscribe to our social media on Facebook: Omnitron i Omnitron Metal Detecting Group and YouTube channel: Michał Majchrowicz and Instagram: sklep_omnitron.

Write under this article what are your experiences with analog devices.

 

Posted on Leave a comment

Coins like mushrooms after rain

The weather always affects the effect of the search and there is no need to cheat. Rain and temperature change the behavior of devices. Sony tends to drift and to put it bluntly, they lose their properties. The result is a decrease in ranges and false signals and interference from the ground. I mean extreme summer temperatures because some manufacturers have been using compensation for the temperature influence on the work of the detector probe for some time.

So how do you defend yourself in such a situation? It’s best to reduce the sensitivity or try ground balance again, even manually for added confidence. There’s an old trick left… we raise the probe above the ground and don’t drive it low. Let’s say 5 cm – 10 cm is the absolute minimum. You may find it much quieter and more stable, and the targets lock in the ID scale better and don’t jump.

Detuning or changing the frequency can also be a solution in this situation. In the end, it remains to wait for the rain, just like mushrooms after rain, previously unheard or immeasurable objects begin to appear.

If you liked this article, please post it on social media and comment on this page.

Posted on Leave a comment

NEXUS Pathfinder V2 hellish frame with discrimination

The frame detector or the popularly known frame is a really great solution for the big game, but unfortunately also very demanding when it comes to the application itself. Everything has to be carefully thought out because the choice is wide and the possibilities are practically unlimited.

The NEXUS company needs no introduction. This is the world of analog detectors, unreasonably expensive, complicated, and IB technology.

So what is the difference between NEXUS products and others, apart from the quality of workmanship? In addition to performance, this type of two-box allows for quick movement over rough terrain and can only be operated by one person. It has discrimination and we are free to choose the type of guide we are looking for! Color or iron and smooth adjustment. Story!

YouTube player

Brilliant solution, considering that with a probe size of 20 inches, we see objects the size of soda cans and larger! There is no problem with small garbage that can make life unbearably difficult. To this, we will add a choice of operating modes: static and dynamic, ground calibration, and mineralization compensation. The extreme amount of iron is not a hindrance, and the device is made of aluminum and carbon fiber and can be quickly folded. The weight is about 4.5 kg, quite bearable.

Finally, the speed of work and we have a really nice daemon that is handy and easy to use. What is the voltage on the probes, I’m afraid to ask, and the large heat sink below the control panel is impressive. Below is a table presenting the capabilities of the Nexus Pathfinder V2.